J&J MACHINE Call (806) 559-1038
Welding at J&J Machine, sparks flying

People Driven • Purpose Built

Machining,repair andfabrication.

Oil and gas, structural, construction, cotton gins and one-off custom parts, from a one-man shop in Wolforth, Texas. If it's broken, worn out or needs to be made, bring it in.

~20 yearsin the trade
2023J&J Machine opened

When you call, you get me.

I started in a machine shop at fourteen and never left the trade. That's nearly twenty years now. I learned it the way machinists always have: on the shop floor at Northern Lucas Machine, working alongside men with decades in the trade. Ten years there running just about every machine in the shop, then Lone Star Bearing, then J&J Machine in 2023.

Today I handle machining, repair and fabrication for oil and gas, structural and construction work, plus one-off custom parts. Cotton gins are where I cut my teeth, and I still keep plenty of West Texas gins running.

No advertising, no middlemen. Just word of mouth and work done right.

— Jason McDonald, owner

Read my story →
Inside the J&J Machine shop: lathes, mills, tool boxes and a cart of bored tubing

Before and after

What comes in the door, and what goes back out.

Rethreading a lint cleaner saw on the lathe.

Lint cleaner saws

Rewraps done the old-school way on a Monarch lathe, one wrap at a time, so the wire goes on tight and stays put. Guaranteed.

  1. Check and rethread. Shafts, keyways and heads get checked, and the groove gets cut fresh when it needs it.
  2. Wrap under tension. The wire is set in the groove and wound on with the lathe following the thread, held tight the whole way so it seats.
  3. Lock it down. A hardened spur wheel locks the wire into the thread, and every inch gets checked so nothing moves.
  4. Balance. Finished saws are dynamically balanced before they go back to the gin.
Close-up of saw wire wound tight in the groove, before it's locked down
Wire wound tight before locked down.
A finished lint cleaner saw, wire wrapped tight, with X marks stamped into the end of the wire

My mark on every saw

Look at the end of the wire. Those X's are my stamp, and they go on every saw I wrap. When you see them, you know who did the work, and you know it's guaranteed.

Move over the photo, or tap it, to look closer.

On the machines

Straight from the shop floor.

A lint cleaner saw in the lathe, ready to wrap
A lint cleaner saw in the lathe, ready to wrap.
Face milling a grid bar.
Rigging a long fluted roller with the chain hoist
Big parts, handled with care.

More from the shop

Tap any photo to see it bigger.

Bring it by or give me a call

Tell me what you've got, and I'll tell you straight what it'll take. Bring the old part, a drawing or just a description, and we'll figure it out.

Shop9729 Highway 62/82
Wolforth, Texas
Get directions
The J&J Machine sign on Highway 62/82 on a foggy morning, with a planter of mums underneath

Made to order

Rebuilds

Parts we sell

Call (806) 559-1038 for pricing

← Back to home

My story

I've been around machine shops since I was fourteen, nearly twenty years now. I started out sweeping floors and mowing the yard at Northern Lucas Machine, and I kept working there through high school in a work program. I couldn't drive yet, so my grandma took me to work. Every chance I got, including my lunch breaks, I was in the back on the machines, and the old-timers took me under their wing. Machinists with decades in the trade showed me how to set up a job and do it right, and they held me to their standard. That's how this trade has always been passed down: on the shop floor, one job at a time. Over ten years there I learned to run just about every machine in the shop. I also went out in the field with the service crew, and sometimes we'd build parts during the day and install them that same night.

In 2017 I went to Lone Star Bearing. I'm still close with the people I worked alongside at Northern Lucas and Lone Star Bearing. In this trade, relationships are everything.

Then one day I was delivering parts to Joe's gin repair shop and joked, "When are you gonna retire and sell this place?" He called me that night and asked if I was serious. I was.

We wanted to keep the Double J name, but that fell through at the last minute, so in 2023 it became J&J Machine. People know it now, so it stays.

Cotton gins are where I cut my teeth, and they're still a big part of what I do. But I'll take on just about any job that comes through the door: oil and gas, structural, construction, or a one-off part somebody can't find anywhere else. I've never spent a dime on advertising. Every customer I have came from a handshake, a phone call, or somebody saying, "Go see Jason." I don't take that lightly. When you call J&J Machine, you get me, and I'll treat your equipment like it's my own.

— Jason McDonald

People Driven • Purpose Built

Age 14Sweeping floors at Northern Lucas Machine
10 yearsTrained on every machine, plus field service
2017Lone Star Bearing
2023J&J Machine opens in Wolforth
Jason and his brother grinning in the shop door, a new CNC lathe strapped on a trailer behind them
The day the CNC lathe came home.
Torch cutting a bearing in the shop, sparks flying past a screen drum
Torching a bearing in the shop.

Call (806) 559-1038